A heat pump can deliver several units of heat for every unit of electricity it uses. That sounds like an easy way to cut energy costs until a homeowner compares an expensive electricity tariff with a cheaper gas tariff. The equipment's efficiency matters, but the actual bill depends on fuel prices, the heating system it replaces and how the building performs in winter. A useful comparison starts with delivered heat and the household's real rates, not a manufacturer's efficiency headline.

Neither experience settles whether heat pumps are efficient. The answer depends on what they replaced, local energy prices, building insulation, the heating system and the weather. A heat pump can deliver several units of heat for each unit of electricity it consumes, but a highly efficient device can still be expensive to run where electricity costs much more than the alternative fuel.

Buying a heat pump is therefore both an engineering decision and a household budgeting exercise. A product rating is part of the calculation, not the calculation itself.

Why a heat pump is different from an electric heater

A resistance heater converts electricity into heat. A heat pump uses electricity mainly to move heat from one place to another. In heating mode, an air-source heat pump extracts energy from outdoor air and transfers it indoors. In cooling mode, it reverses the process, removing heat from a room.

Because it moves heat, a heat pump can deliver more thermal energy than the electrical energy it consumes. Its efficiency is often expressed as a coefficient of performance, or COP. A COP of 3 means that, under the conditions being measured, one unit of electricity delivers about three units of heat.

The number varies with outdoor temperature, indoor settings and the equipment's operating conditions. Cold weather can reduce output and efficiency for some designs, although modern cold-climate equipment can operate in low temperatures. Defrost cycles, backup heating and system controls can affect real seasonal consumption.

A home should be evaluated using performance appropriate to its climate, not only a laboratory rating measured under one favorable condition.

The US Department of Energy's purchasing guidance for residential air-source heat pumps compares equipment using standardized seasonal ratings and illustrative costs. The examples depend on test assumptions; they are not universal predictions for an individual home.

The ratio that changes the result

A simple cost comparison can reveal why a highly efficient technology sometimes disappoints on bills.

Suppose a household needs 10,000 kilowatt-hours of useful heat over a heating season. If a heat pump delivers a seasonal COP of 3, it uses roughly 3,333 kWh of electricity for that heating load. At an illustrative electricity price of $0.20 per kWh, heating electricity would cost about $667.

Now compare a gas boiler operating at an assumed seasonal efficiency of 90%. It would need approximately 11,111 kWh of fuel input to deliver the same useful heat. At a hypothetical gas price of $0.07 per kWh, that comes to about $778.

The heat pump is cheaper in that simplified example. Change electricity to $0.30 per kWh, keeping the other values unchanged, and its heating energy cost rises to approximately $1,000. It is now more expensive on energy alone.

These are teaching calculations, not retail price quotes or installation estimates. They omit standing charges, maintenance, distribution losses and other components of a real bill. They also assume the heating load and comfort level remain the same. Their point is that equipment efficiency and energy price must be considered together.

The International Energy Agency's analysis of heat pumps in poorly insulated homes makes precisely this distinction. It finds that savings vary substantially with insulation and the relative price of electricity and gas. Homes in markets with expensive electricity relative to gas may see much smaller bill reductions or, in some circumstances, higher costs.

Insulation can change the equipment you need

A heating system must supply enough heat to maintain comfortable indoor temperatures on a cold day. A poorly insulated house leaks heat faster, forcing the equipment to work harder. Improving insulation, airtightness and windows can reduce the heating load, sometimes allowing a smaller or less costly system.

The relationship is particularly important when replacing a high-temperature boiler with a heat pump. Some houses use radiators or distribution systems designed around hotter water than a heat pump operates with most efficiently. Low-temperature-compatible radiators, underfloor heating or other distribution upgrades may be appropriate.

That does not mean every house needs a complete renovation first. The right sequence depends on the building, budget and existing equipment. Basic measures such as sealing obvious air leaks can be relatively inexpensive; structural upgrades may be costly and disruptive.

Ask a qualified installer to perform a heat-loss assessment and explain what operating temperatures the system will require. An estimate based only on square footage or the capacity of the old boiler may miss important differences in insulation and comfort preferences.

A homeowner comparing quotes should know whether proposed insulation improvements are part of the heat pump's cost case or assumed to have been completed already.

Running cost is not total ownership cost

Even if a heat pump uses less energy, the initial investment can be significant. The full project may include outdoor and indoor units, electrical work, pipework, duct modifications, radiators or water-storage equipment. Prices vary sharply by country, property and installer.

A fair comparison includes the alternative. If an old boiler is failing, the relevant decision may be between a new boiler and a heat pump rather than between spending nothing and buying a heat pump. If the home already needs cooling, a heat pump that provides both heating and cooling may replace more than one appliance.

Financial incentives complicate the calculation further. Rebates, grants, loan programs and energy tariffs change over time and can be restricted to specific equipment or eligible households. Check the rules currently applicable to the property rather than relying on a promotional example from another country.

Maintenance and expected service life also matter. Some costs arise every year; others are rare but large. A responsible comparison states the assumptions behind any payback estimate and shows how the answer changes under higher energy prices, lower efficiencies or unexpected repairs.

A claim that all heat pumps "pay for themselves in five years" is too broad to be useful without those details.

Why global benefits can coexist with local cost problems

The IEA's Heat Pump Monitor 2026 describes heat pumps as a way to reduce fossil-fuel demand for heating and improve energy-system flexibility under suitable conditions. It estimates that existing installations avoided substantial natural-gas use in Europe, Japan and China in recent years.

Those are system-level estimates, not guarantees of savings for a particular household. A technology can deliver energy-security or emissions benefits on a large scale while an individual installation faces expensive electricity, unsuitable distribution equipment or a poor building envelope.

Electricity generation also affects emissions. A heat pump's carbon footprint depends partly on the power system serving it, the refrigerant used, equipment efficiency and installation quality. The environmental comparison can change over time as a country's electricity mix evolves.

For policy, this means grants for equipment may work better alongside building-efficiency improvements, technician training and electricity-market reforms. For homeowners, it means a national energy narrative should not replace a tailored quote.

Comfort and controls can make the real difference

A system designed to operate steadily at moderate temperatures may be used differently from a boiler that produces a burst of high-temperature heat. Households sometimes change thermostat habits after installation. If the installer has not explained the controls, those changes can produce confusion and unexpected bills.

Good commissioning should verify that the heat pump, emitters, controls and backup heater work together. A badly configured backup system can consume more electricity than expected. Airflow problems, blocked filters or unsuitable settings may also reduce performance.

Ask what happens on the coldest expected day, how the backup heat is triggered and whether there is a way to monitor electrical consumption separately from other household use. If the system supports cooling, ask how summer electricity demand is reflected in the projected annual costs.

Some installers quote peak efficiency under favorable conditions. Request a seasonal estimate that reflects the local climate and the home. Where possible, review examples from comparable homes, while recognizing that different occupants and buildings can produce different outcomes.

A well-designed installation is more than equipment delivery. It includes correct sizing, commissioning and a homeowner who understands how to operate the system.

A seven-question quote checklist

Before accepting a proposal, ask the installer to document:

  1. The estimated annual useful heating demand and the method used to calculate it.
  2. The expected seasonal efficiency under local weather and proposed water or air temperatures.
  3. The assumed electricity and alternative-fuel prices, with standing charges identified separately.
  4. The exact insulation or radiator changes included in the quotation.
  5. How backup heating, defrost and hot-water preparation affect consumption.
  6. Upfront cost, maintenance assumptions, warranty scope and any incentive eligibility.
  7. The sensitivity of the estimate to colder weather and higher electricity tariffs.

A competent comparison should answer the same questions for the alternative heating system. If the vendor cannot explain the assumptions, the quoted monthly savings are difficult to trust.

A heat pump can be an excellent investment in comfort and efficiency. Its financial case is strongest when it is matched to the building and the energy market rather than chosen from a universal savings promise.

SOURCES & FURTHER READING

References and background

Our explainers link to source documents so readers can explore the evidence and interpret it in context. Websites and policies may change after publication.

  1. IEA, *Does a heat pump work in a house with poor insulation?* (2024)www.iea.org
  2. IEA, *Heat Pump Monitor 2026: Key Findings*www.iea.org
  3. US Department of Energy, *Purchasing Energy-Efficient Residential Air-Source Heat Pumps*www.energy.gov
Spot a factual issue? Request a correction ↗Read our editorial standards ↗